About the Analog Electronics MCQ category
|
|
0
|
183
|
March 25, 2021
|
The varactor is a type of pn junction that acts as which of the ___
|
|
0
|
52
|
June 18, 2022
|
The PREFERRED solder alloy ratio for electronic repair is ___
|
|
0
|
49
|
May 31, 2022
|
A roll of solder is marked ___
|
|
0
|
47
|
May 31, 2022
|
Solder used in electronics is an alloy composed of which of the following metals?
|
|
0
|
45
|
May 31, 2022
|
Regardless of location, 2M repair stations require adequate ___
|
|
0
|
42
|
May 31, 2022
|
The handpiece that can be used for the greatest variety of operations is ___
|
|
0
|
30
|
May 31, 2022
|
In the selection of a soldering iron tip, which of the following factors should be considered?
|
|
0
|
37
|
May 31, 2022
|
2M repair stations are equipped according to the types of repairs to be ___
|
|
0
|
30
|
May 31, 2022
|
During fault isolation procedures, a device or component should be ___
|
|
0
|
34
|
May 31, 2022
|
Fault diagnosis using GPETE should only be attempted by which of the following personnel?
|
|
0
|
30
|
May 31, 2022
|
Which of the following types of test equipment is classified as off-line automatic test equipment?
|
|
0
|
25
|
May 31, 2022
|
A dc voltmeter that is permanently attached to a power supply for ___
|
|
0
|
56
|
May 31, 2022
|
Test equipment that continuously monitors performance and ___
|
|
0
|
71
|
May 31, 2022
|
Source, Maintenance, and Recovery (SM & R) codes that ___
|
|
0
|
33
|
May 31, 2022
|
Boards or modules that are SM & R code D may be repaired at ___
|
|
0
|
57
|
May 31, 2022
|
The maintenance level at which normal 2M repairs are performed is ___
|
|
0
|
29
|
May 31, 2022
|
Inspecting, servicing, and adjusting equipment is the function of ___
|
|
0
|
33
|
May 31, 2022
|
Direct support to user organizations is provided by ___
|
|
0
|
33
|
May 31, 2022
|
SM & R code D maintenance facilities are usually located at which of the following activities?
|
|
0
|
31
|
May 31, 2022
|
The most extensive shop facilities and highly skilled technicians are ___
|
|
0
|
40
|
May 31, 2022
|
If a technician should fail to maintain the required standards of ___
|
|
0
|
24
|
May 31, 2022
|
To ensure that a 2M technician maintains the minimum standards of ___
|
|
0
|
26
|
May 31, 2022
|
Repairs that are limited to discrete components and ___
|
|
0
|
24
|
May 31, 2022
|
A technician is authorized to perform 2M repairs upon satisfactory completion of ___
|
|
0
|
23
|
May 31, 2022
|
The standards of workmanship and guidelines for specific repairs to ___
|
|
0
|
28
|
May 31, 2022
|
Training requirements for miniature and ___
|
|
0
|
29
|
May 31, 2022
|
Ground planes and shielding are used to prevent ___
|
|
0
|
47
|
May 31, 2022
|
Environmental performance requirements for ICs are set forth in ___
|
|
0
|
31
|
May 31, 2022
|
The most complex to produce and difficult to repair ___
|
|
0
|
28
|
May 31, 2022
|