Which one of the following could be responsible for the difference between the initial and current steady-state conditions for the throttle valve ___
|
|
0
|
220
|
March 4, 2021
|
Subcooled water is flowing through a throttle valve in an open system ___
|
|
0
|
128
|
March 4, 2021
|
The valve that typically requires the least linear travel of the disk from fully closed to fully open is the ___ valve; and the valve that produces the greatest pressure drop when fully open is the ___ valve
|
|
0
|
156
|
March 4, 2021
|
Refer to the drawing of an operating cooling water system (see figure below) in which valves A and B are identical ___
|
|
0
|
181
|
March 4, 2021
|
Subcooled water is flowing through a throttle valve in an open system. The initial steady-state conditions for the throttle valve are as follows ___
|
|
0
|
150
|
March 4, 2021
|
Subcooled water was flowing through a throttled valve with the following initial parameters ___
|
|
0
|
140
|
March 4, 2021
|
Consider a 6-inch globe valve and a 6-inch gate valve in the same water system application ___
|
|
0
|
253
|
March 4, 2021
|
Refer to the centrifugal pump operating curve with two system head loss curves ___
|
|
0
|
153
|
March 4, 2021
|
Which one of the following types of similarly sized valves in an operating water system produces the least frictional head loss when fully open ___
|
|
0
|
498
|
March 4, 2021
|
Refer to the drawing of a cooling water system in which both centrifugal pumps A and B are operating ___
|
|
0
|
177
|
March 4, 2021
|
Which one of the following statements describes the throttling characteristics of a typical globe valve ___
|
|
0
|
196
|
March 4, 2021
|
Which one of the following statements describes the flow rate characteristics of a typical globe valve in an operating water system ___
|
|
0
|
127
|
March 4, 2021
|
A control valve is most likely to experience cavitation when the valve is almost fully ___ because of a relatively ___ pressure drop across the valve seat
|
|
0
|
1023
|
March 4, 2021
|
Consider a typical gate valve and a typical globe valve in the same water system application ___
|
|
0
|
247
|
March 4, 2021
|
Which one of the following statements describes the flow rate characteristics of a typical gate valve in an operating water system ___
|
|
0
|
121
|
March 4, 2021
|
If a pressure control valve at the outlet of a heat exchanger opens farther, system flow rate will ___; and system head loss will ___
|
|
0
|
232
|
March 4, 2021
|
The tank is protected by two relief valves that discharge to the atmosphere. The relief valves have the following characteristics ___
|
|
0
|
128
|
March 4, 2021
|
A cooling water system uses a conventional relief valve (not pilot-operated) with a bench-tested setpoint of 60 psig ___
|
|
0
|
141
|
March 4, 2021
|
A completely full water storage tank is being hydrostatically tested to 300 psig using a positive displacement pump (PDP) with a smooth and constant discharge flow rate of 4 gpm ___
|
|
0
|
126
|
March 4, 2021
|
A completely full water storage tank is being hydrostatically tested to 200 psig using a positive displacement pump (PDP) with a smooth and constant discharge flow rate of 4 gpm ___
|
|
0
|
250
|
March 4, 2021
|
A completely full water tank is being hydrostatically tested to 180 psig using a positive displacement pump (PDP) with a smooth and constant discharge flow rate of 6 gpm ___
|
|
0
|
144
|
March 4, 2021
|
A completely full water storage tank is being hydrostatically tested to 200 psig using a positive displacement pump (PDP) with a smooth and constant discharge flow rate of 6 gpm ___
|
|
0
|
149
|
March 4, 2021
|
Vessels A and B are identical except that vessel A receives overpressure protection from an installed safety valve ___
|
|
0
|
167
|
March 4, 2021
|
Water storage tanks A and B are identical except that tank A receives overpressure protection from a relief valve, whereas tank B uses a safety valve ___
|
|
0
|
135
|
March 4, 2021
|
Which one of the following is a difference between a typical relief valve and a typical safety valve ___
|
|
0
|
529
|
March 4, 2021
|
Refer to the drawing of two identical pressure vessels with identical relief valve protection. Both vessels have been pressurized to 50 psig and then isolated ___
|
|
0
|
269
|
March 4, 2021
|
The difference between the setpoint pressure at which a safety valve opens and the pressure at which it closes is called ___
|
|
0
|
325
|
March 4, 2021
|
The difference between the setpoint pressure at which a relief valve begins to open and the pressure at which it is fully open is called ___
|
|
0
|
214
|
March 4, 2021
|
Refer to the drawing of two identical pressure vessels with identical relief valve protection ___
|
|
0
|
238
|
March 4, 2021
|
The tank is protected by a relief valve and a safety valve that both discharge to the atmosphere. The valves have the following characteristics ___
|
|
0
|
212
|
March 4, 2021
|